EZH2O
®
Bottle Filling Station
with Bi-Level Reverse Filtered LZ Cooler
Models LZSTLR8WS & LZSTLRDDWS
2222 Camden Court
Oak Brook, IL 60523
elkaypro.com
Printed in U.S.A.
© 2014 Elkay
RATED FOR INDOOR USE ONLY
C
L
C
L
2"
51mm
5 3/4"
146mm
7"
178mm
7"
178mm
19 7/16"
494mm
34 5/16"
872mm
2"
51mm
2 7/8"
73mm
15"
381mm
6 3/8"
162mm
6 3/8"
162mm
22 15/16"
583mm
24 1/2"
622mm
E
A
PREFERRED
LOCATION
B
7/16" X 3/4" OBROUND
(11mm X 19mm) HOLES (6)
3"
77mm
19"
483mm
HANGER BRACKET
8 1/16"
205mm
9/32"
O
HOLES
(7mm) (12)
c
1 7/16"
37mm
27"
686mm
ADA
REQUIREMENT
12 1/2"
318mm
D
PREFERRED
LOCATION
A
ALTERNATE
LOCATION
6 3/8"
162mm
6 3/8"
162mm
31 5/16"
796mm
RIM
HEIGHT
32 7/8"
835mm
ORIFICE
HEIGHT
13 15/16"
354mm
17 7/16"
443mm
21 7/8"
556mm
F
28 13/16"
732mm
2"
51mm
18 3/8"
467mm
7"
178mm
7"
178mm
7/8"
22mm
2"
51mm
3 7/8"
98mm
D
ALTERNATE
LOCATION
F
3 9/16"
90mm
38 3/8"
975mm
ORIFICE
HEIGHT
17 7/8"
454mm
FINISHED FLOOR
REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDRENS ADA COOLER
Job Name: ____________________________________
Model: _______________________ Qty. ____________
Contact: ______________________________________
Approval Signature: _____________________________
Notes:
LEGEND:
A = Recommended Water Supply location. Shut-off Valve (not furnished) to accept
3/8” O.D. unplated copper tube. Up to 3” (76mm) maximum out from wall.
B = Recommended Waste Outlet location. To accommodate 1-1/2” nominal drain.
Drain stub 2” (51mm) out from wall.
C = 1-1/2” Trap (not furnished).
D = Electrical Supply (3) Wire Recessed Box Duplex Outlet.
E = Insure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet
louvers to wall.
F = 7/16” (11mm) Bolt Holes for fastening to wall.
**New Installations Must Use Ground Fault Circuit Interrupter (GFCI).
NOTICE
This water cooler must be connected to the water supply using a dielectric
coupling. The cooler is furnished with a non- metallic strainer which meets this
requirement. The drain trap which is provided by the installer should also be
plastic to completely isolate the cooler from the building plumbing system.
IMPORTANT! INSTALLER PLEASE NOTE:
These units are designed and built to provide water to the user which has not
been altered by materials in the cooler waterway. The grounding of electrical
equipment such as telephone, computers, etc. to water lines is a common
procedure. This grounding may be in the building but may also occur away from
the building. This grounding can cause electrical feedback into a water cooler
creating an electrolysis which results in a metallic taste or an increase in the
metal content of the water. This condition is avoidable by installing the cooler
using the proper materials as shown.
Bottle Filler unit will mount on bracket attached to wall by 6 holes (as shown).
Water and electrical will connect through pre-punched hole in basin.
ROUGH-IN
Model shown with Flexi-Guard StreamSaver Bubbler.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals